Akron Highsider [車用品・バイク用品]
154件中 1件 - 30件
1 2 3 4 5 6
| 商品 | 説明 | 価格 |
|---|---|---|
 Highsider ハイサイダー Akron-XL ハンドルバーウエイト ウェビック 楽天市場店 | ■商品概要【メーカー品番】161-0570カラー：ブラック■詳細説明HIGHSIDER AKRON-XS motorcycle Bar End Weights- Styling for your bike -With these nobly designed handlebar ends you can design your bike in detail according to your ideas． Handlebar ends also serve to reduce annoying vibrations on the handlebars． Thanks to clamping system with different sleeves universal suitable for 7/8 (Φ22 mm)， 1 inch (Φ25，4 mm) or X-Bar (Φ28，6 mm) tube handlebars with an inner diameter from 12 to 22 mm．Our accessories TIP:Excellent in combination with the visually coordinated design LENKERGRIFFGUMMIS from our own house． The caps of the handlebar ends mirror the design of the grip rubbers and make your motorcycle cockpit an eye-catcher．Precisely matched - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle． With a maximum of quality and functionality you can easily design your bike according to your wishes．Dimensions:Stem weightΦ: 37，4 mmWidth: 17 mmScope of supply: 1 pair incl．2 clamping sleeves each with D． 12 mm and D． 16 mm2 spacer sleeves each with D． 14 mm， D． 18 mm and D． 21 mm2 x M6 central screws2 x M6 cone nutsNOTE:For Bar End Weights with clamping system， the ends of the handlebars must not be blocked by threaded inserts or similar．Steering ends do not have to be approved， therefore do not require any test marks， certificates or ABEs．■注意点※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■商品番号1108559001 | 7,657円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) ER-6 F (EX650E) ER-6 F ABS (EX650F) ER-6 N (ER650E) ER-6 N ABS (ER650F) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-706H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS turn signal brackets are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesThe scope of delivery of the AKRON-RS includes: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Note:The special turn signal bracket 280-974 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種ER-6 F (EX650E) ER-6 F (EX650E) 年式: 12-16 ER-6 F ABS (EX650F) ER-6 F ABS (EX650F) 年式: 12-16 ER-6 N (ER650E) ER-6 N (ER650E) 年式: 12-16 ER-6 N ABS (ER650F) ER-6 N ABS (ER650F) 年式: 12-16 ■商品番号1108206 | 14,469円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) YZF-R125 ABS (RE39) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-923H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-related bracket with mounting parts - HIGHSIDER AKRON-RS license plate retaining plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - For the original turn signals the special turn signal holder 280-970 is optionally available． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種YZF-R125 ABS (RE39) YZF-R125 ABS (RE39) 年式: 19-21 ■商品番号1108337 | 14,469円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) CBR 600 RR (PC40) CBR 600 RR ABS (PC40) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-603H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-related bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European license plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-related bracket with mounting parts - HIGHSIDER AKRON-RS license plate retaining plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - Since the original tail light of your motorcycle is omitted when mounting this license plate holder， we offer you a suitable replacement in the accessories tab． There you will find our modern and for road traffic approved 3in1 combinations． - If your original number plate holder has reflectors fitted to the side， these must be refitted in a suitable position or replaced with new ones． - For the original turn signals we offer you， also in the tab accessories， optionally a special turn signal holder． Tips: If you have not found a model-specific license plate holder for your vehicle， then you will certainly find the universal license plate holders from HIGHSIDER， which are available in many different designs．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種CBR 600 RR (PC40) CBR 600 RR (PC40) 年式: 07-12 CBR 600 RR ABS (PC40) CBR 600 RR ABS (PC40) 年式: 09-12 ■商品番号1108162 | 20,649円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー CB650F CBR650 ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-610HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS PRO’s turn signal brackets are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light Included with the AKRON-RS PRO are: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-approved reflector with adjustable bracket - E-approved license plate light - Mounting instructions Note:The special 280-973 turn signal bracket is available as an option for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種CB650F CB650F CBR650 CBR650 ■商品番号1108173 | 18,588円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) 950 HYPERMOTARD 950 HYPERMOTARD RVE 950 HYPERMOTARD SP ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-165H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-related bracket with mounting parts - HIGHSIDER AKRON-RS license plate retaining plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - The special turn signal holder 280-969 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種950 HYPERMOTARD 950 HYPERMOTARD 年式: 19-21 950 HYPERMOTARD RVE 950 HYPERMOTARD RVE 年式: 21 950 HYPERMOTARD SP 950 HYPERMOTARD SP 年式: 19-21 ■商品番号1108107 | 18,588円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-404H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-related bracket with mounting parts - HIGHSIDER AKRON-RS license plate retaining plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - The special turn signal holder 280-978 is optionally available for the original turn signals． Tips: If you have not found a model-specific license plate holder for your vehicle， then you will certainly find the universal license plate holders from HIGHSIDER， which are available in many different designs．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種DAYTONA 675 ABS DAYTONA 675 ABS 年式: 13-17 DAYTONA 675 R ABS DAYTONA 675 R ABS 年式: 13-17 STREET TRIPLE 660 S ABS A2 STREET TRIPLE 660 S ABS A2 年式: 17-19 STREET TRIPLE 675 STREET TRIPLE 675 年式: 13 STREET TRIPLE 675 ABS STREET TRIPLE 675 ABS 年式: 13-17 STREET TRIPLE 675 R STREET TRIPLE 675 R 年式: 13 STREET TRIPLE 675 R ABS STREET TRIPLE 675 R ABS 年式: 13-17 STREET TRIPLE 675 RX ABS STREET TRIPLE 675 RX ABS 年式: 15-16 STREET TRIPLE 765 R ABS STREET TRIPLE 765 R ABS 年式: 17-21 STREET TRIPLE 765 RS ABS STREET TRIPLE 765 RS ABS 年式: 17-21 STREET TRIPLE 765 S ABS STREET TRIPLE 765 S ABS 年式: 17-20 ■商品番号1108149 | 21,268円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) YZF-R125 (RE11) YZF-R125 ABS (RE11) YZF-R125 ABS (RE29) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-914H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-related bracket with mounting parts - HIGHSIDER AKRON-RS license plate retaining plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - For the original turn signals the special turn signal holder 280-970 is optionally available． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種YZF-R125 (RE11) YZF-R125 (RE11) 年式: 14-16 YZF-R125 ABS (RE11) YZF-R125 ABS (RE11) 年式: 15-16 YZF-R125 ABS (RE29) YZF-R125 ABS (RE29) 年式: 17-18 ■商品番号1108318 | 14,469円 |
 Highsider ハイサイダー Akron-XL ハンドルバーウエイト ウェビック 楽天市場店 | ■商品概要【メーカー品番】161-0583標準カラー：マットチタン■詳細説明HIGHSIDER AKRON-XL Bar End Weights- Styling for your bike -With these nobly designed handlebar ends you can design your bike in detail according to your ideas． Handlebar ends also serve to reduce annoying vibrations on the handlebars． Thanks to clamping system with different sleeves universal suitable for 7/8 (Φ22 mm)， 1 inch (Φ25，4 mm) or X-Bar (Φ28，6 mm) tube handlebars with an inner diameter from 12 to 22 mm．Our accessories TIP:Excellent in combination with the visually coordinated design LENKERGRIFFGUMMIS from our own house． The caps of the handlebar ends mirror the design of the grip rubbers and make your motorcycle cockpit an eye-catcher．Precisely matched - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle． With a maximum of quality and functionality you can easily design your bike according to your wishes．Dimensions:Bar End WeightsΦ: 37，4 mmWidth: 34 mmScope of supply: 1 pair incl．Each 2 clamping sleeves with D． 12 mm and D． 16 mmEach 2 spacer sleeves with D． 14 mm， D． 18 mm and D． 21 mm2 x M6 central screws2 x M6 conical nutsNOTE:For Bar End Weights with clamping system， the ends of the handlebars must not be blocked by threaded inserts or similar．Steering ends do not have to be approved， therefore do not require any test marks， certificates or ABEs．■注意点※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■商品番号1108560003 | 8,760円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) 690 ENDURO R ABS 690 SUPERMOTO SMC R ABS ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-308H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS turn signal brackets are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesIncluded with the AKRON-RS are: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - For the original turn signals the special turn signal holder 280-975 is optionally available． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種690 ENDURO R ABS 690 ENDURO R ABS 年式: 14-16 690 SUPERMOTO SMC R ABS 690 SUPERMOTO SMC R ABS 年式: 14-16 ■商品番号1108123 | 14,469円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-404HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS PRO’s turn signal brackets are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light Included with the AKRON-RS PRO are: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-approved reflector with adjustable bracket - E-approved license plate light - Mounting instructions Note:The special 280-978 turn signal bracket is available as an option for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， then you will certainly find the universal license plate holders from HIGHSIDER， which are available in many different designs．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■商品番号1108150 | 18,588円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) Z 900 A2 ABS (ZR900D) Z 900 A2 ABS (ZR900H) Z 900 ABS (ZR900B) Z 900 ABS (ZR900F) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-724H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS turn signal brackets are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesThe scope of delivery of the AKRON-RS includes: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Note:The special turn signal bracket 280-974 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種Z 900 A2 ABS (ZR900D) Z 900 A2 ABS (ZR900D) 年式: 18-19 Z 900 A2 ABS (ZR900H) Z 900 A2 ABS (ZR900H) 年式: 20-21 Z 900 ABS (ZR900B) Z 900 ABS (ZR900B) 年式: 17-19 Z 900 ABS (ZR900F) Z 900 ABS (ZR900F) 年式: 20-21 ■商品番号1108246 | 14,469円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) ER-6 F (EX650A) ER-6 F ABS (EX650B) ER-6 N (ER650A) ER-6 N ABS (ER650B) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-704H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-related bracket with mounting parts - HIGHSIDER AKRON-RS license plate retaining plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - The special turn signal holder 280-974 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種ER-6 F (EX650A) ER-6 F (EX650A) 年式: 06-08 ER-6 F ABS (EX650B) ER-6 F ABS (EX650B) 年式: 06-08 ER-6 N (ER650A) ER-6 N (ER650A) 年式: 06-08 ER-6 N ABS (ER650B) ER-6 N ABS (ER650B) 年式: 06-08 ■商品番号1108202 | 14,469円 |
 Highsider ハイサイダー Akron-LS バーエンド ウェビック 楽天市場店 | ■商品概要【メーカー品番】161-0591標準カラー：シルバー■詳細説明HIGHSIDER AKRON-LS Bar End Weights， black with cap in different colors- Styling for your bike -With these nobly designed Bar End Weights with handlebar end mirror receptacle， you can design your bike in detail according to your ideas． These end pieces are used for all HIGHSIDER & SHIN YO handlebar end mirrors with handlebar outer clamp． Handlebar ends also serve to reduce annoying vibrations on the handlebars． Thanks to clamping system with different sleeves universal suitable for 7/8 (Φ22 mm)， 1 inch (Φ25，4 mm) or X-Bar (Φ28，6 mm) tube handlebars with an inner diameter from 12 to 22 mm．Our accessories TIP:Excellent in combination with the visually coordinated design LENKERGRIFFGUMMIS AKRON from our own house． The caps of the handlebar ends mirror the design of the grip rubbers and make your motorcycle cockpit an eye-catcher． If you do want to switch back to handlebar mirrors， you can easily use the optionally available coloured rings instead of a handlebar end mirror and thus add further colour accents． The colour rings are simply pushed over the end of the handlebar and fastened with the grub screw located on the ring．Precisely matched - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle． With a maximum of quality and functionality you can easily design your bike according to your wishes．Dimensions:Bar End WeightsΦ: 37，4 mmWidth: 29 mmMount for mirror: Φ 29，90 mm， Width: 12 mmScope of delivery: 1 pair incl．Each 2 clamping sleeves with D． 12 mm and D． 16 mmEach 2 spacer sleeves with D． 14 mm， D． 18 mm and D． 21 mm2 x M6 central screws2 x M6 cone nutsNOTE:For Bar End Weights with clamping system， the ends of the handlebars must not be blocked by threaded inserts or similar．Steering ends do not have to be approved， therefore do not require any test marks， certificates or ABEs．■注意点※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■商品番号1108561002 | 7,657円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー MT-125 ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-900HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS PRO’s turn signal brackets are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light Included with the AKRON-RS PRO are: - Model-specific bracket with mounting parts - AKRON-RS license plate holder plate - Adjustable turn signal holders - E-tested reflector with adjustable holder - E-tested license plate light - Mounting instructions Notes: - If side reflectors are mounted on your original license plate holder， they must be reattached in a suitable position or replaced with new ones． - The special turn signal holder 280-977 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種MT-125 MT-125 ■商品番号1108296 | 18,588円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー 125Duke 390Duke ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-310HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS PRO’s turn signal brackets are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light Included with the AKRON-RS PRO are: - Model-specific bracket with mounting parts - AKRON-RS license plate holder plate - Adjustable turn signal holders - E-tested reflector with adjustable holder - E-tested license plate light - Mounting instructions Notes: - If side reflectors are mounted on your original license plate holder， they must be reattached in a suitable position or replaced with new ones． - For the original turn signals the special turn signal holder 280-975 is optionally available． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種125Duke 390Duke ■商品番号1108126 | 20,649円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) NINJA 400 ABS (EX400G) NINJA 400 ABS KRT EDITION (EX400G) NINJA 400 ABS SPECIAL EDITION (EX400G) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-727H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-related bracket with mounting parts - HIGHSIDER AKRON-RS license plate retaining plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - The special turn signal holder 280-974 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種NINJA 400 ABS (EX400G) NINJA 400 ABS (EX400G) 年式: 18 NINJA 400 ABS KRT EDITION (EX400G) NINJA 400 ABS KRT EDITION (EX400G) 年式: 18-21 NINJA 400 ABS SPECIAL EDITION (EX400G) NINJA 400 ABS SPECIAL EDITION (EX400G) 年式: 19-20 ■商品番号1108252 | 14,469円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) 690 DUKE 690 DUKE ABS 690 DUKE CUP 690 DUKE R 690 DUKE R ABS 690 DUKE TRACK ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-306H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS turn signal brackets are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesThe scope of delivery of the AKRON-RS includes: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Note:The special turn signal bracket 280-975 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種690 DUKE 690 DUKE 年式: 12 690 DUKE ABS 690 DUKE ABS 年式: 13-19 690 DUKE CUP 690 DUKE CUP 年式: 12 690 DUKE R 690 DUKE R 年式: 12 690 DUKE R ABS 690 DUKE R ABS 年式: 13-17 690 DUKE TRACK 690 DUKE TRACK 年式: 13 ■商品番号1108119 | 16,529円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー S1000R S1000RR ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-104HPカラー：ブラック認証：CE 認証素材：スチール■詳細説明The HIGHSIDER AKRON-RS license plate holder fits perfectly on your motorcycle thanks to its attractive design．The license plate holder is model specific and allows easy mounting on the original mountings without any modifications．Made of 2mm steel and laser cut， the holder has a weather resistant coating．Fully adjustable， you can adjust the holder to the desired position． An additional locking screw ensures that it stays in place．The AKRON-RS turn signal holders are adjustable in width and are therefore suitable for all types of turn signals． This adjustment option allows you to adapt the position of your turn signals to the most diverse license plates． The 10 mm holes are on the side to allow the indicators to be mounted without disconnecting them from the wiring harness．The PRO version of the HIGHSIDER AKRON-RS includes a high-quality aluminum license plate light with mounting plate and support arm． The bracket is height-adjustable and designed for an homolgated mounting．Adjustable reflector， E-approvedSuitable for European license platesAdjustable angle of inclinationAdditional screw for optimal positional safetyEasy mounting without additional drillingEasy mounting of the license plateAdjustable plate light included， holder included■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種S1000R S1000R S1000RR S1000RR ■商品番号1111125 | 21,664円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) NINJA ZX-6 R ABS (ZX636G) NINJA ZX-6 R ABS KRT EDITION (ZX636G) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-730H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-related bracket with mounting parts - HIGHSIDER AKRON-RS license plate retaining plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - The special turn signal holder 280-974 is optionally available for the original turn signals． Tips: If you have not found a model-specific license plate holder for your vehicle， then you will certainly find the universal license plate holders from HIGHSIDER， which are available in many different designs．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種NINJA ZX-6 R ABS (ZX636G) NINJA ZX-6 R ABS (ZX636G) 年式: 19-21 NINJA ZX-6 R ABS KRT EDITION (ZX636G) NINJA ZX-6 R ABS KRT EDITION (ZX636G) 年式: 19-20 ■商品番号1108260 | 14,469円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) 125 DUKE ABS 390 DUKE ABS ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-310H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS turn signal brackets are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesThe scope of delivery of the AKRON-RS includes: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Note:The special turn signal bracket 280-975 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種125 DUKE ABS 125 DUKE ABS 年式: 17-21 390 DUKE ABS 390 DUKE ABS 年式: 17-21 ■商品番号1108125 | 16,529円 |
 Highsider ハイサイダー Akron-X LED テールライト ブレーキ ライト ターンシグナル ウェビック 楽天市場店 | ■商品概要【メーカー品番】254-2792認証：CE 認証素材：アルミニウムカバーカラー：スモークライトタイプ：LEDポジション：フロント/リアパッキング : 1ペアBiカラー：ブラック/レッド■詳細説明HIGHSIDER AKRON-X LED taillight， brake light， turn signal- Timelessly elegant look， state-of-the-art technology -Flowing shapes and perfect transitions characterize the appearance of the HIGHSIDER AKRON-X， on top of that it presents itself in just the right size． The light of the HIGHSIDER AKRON-X is an announcement that unmistakably indicates which way is up． The two powerful SMD’s show their best side with this shapely add-on parts with tinted reflector． Equipped with a particularly beautiful light pattern， the direction indicator shines or flashes brightly and strongly． Look forward to this elegant direction indicator whose form and function blend beautifully． Be seen with safety - the tail light/indicator series from HIGHSIDER give you the safety you need and the look you want - whether you’re riding a Cafe racer， chopper or naked bike． Dimensions: A diameter: 40 mm Depth: 45 mm Thread: M8， length 20 mmStalk approx．: 15 mmConnections: Yellow = Turn signal (+) Red = Brake (+)White = Taillight (+) Black = Ground (-) Scope of delivery: 1 pair■注意点※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■商品番号1108649002 | 27,531円 |
 Highsider ハイサイダー Akron-X LED ターンシグナル ウェビック 楽天市場店 | ■商品概要【メーカー品番】204-2792標準カラー：レッド■詳細説明HIGHSIDER AKRON-X LED turn signal- Timeless elegant look. state-of-the-art technology -Flowing shapes and perfect transitions characterize the appearance of the HIGHSIDER AKRON-X. on top of that it presents itself in just the right size. The light of the HIGHSIDER AKRON-X is an announcement that unmistakably indicates which way is up. The two powerful SMD's show their best side with this shapely add-on parts with tinted reflector. Equipped with a particularly beautiful light pattern. the direction indicator shines or flashes brightly and strongly. Look forward to this elegant direction indicator whose form and function blend beautifully.Be seen with safety - the turn signal series from HIGHSIDER give you the safety you need and the look you want - whether it's a cafe racer. chopper or naked bike.Dimensions:A diameter: 40 mmDepth: 45 mmThread: M8. length 20 mmStem approx: 15 mmConnections:Yellow = indicator (+)Black = ground (-)Scope of delivery: 1 pair■注意点※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■商品番号1108582002 | 20,649円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) MT-03 ABS (RH07) MT-03 ABS (RH12) YZF-R3 ABS (RH07) YZF-R3 ABS (RH12) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-917H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged bushings are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-related bracket with mounting parts - HIGHSIDER AKRON-RS license plate retaining plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - The special turn signal holder 280-977 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種MT-03 ABS (RH07) MT-03 ABS (RH07) 年式: 16-17 MT-03 ABS (RH12) MT-03 ABS (RH12) 年式: 18 YZF-R3 ABS (RH07) YZF-R3 ABS (RH07) 年式: 15-17 YZF-R3 ABS (RH12) YZF-R3 ABS (RH12) 年式: 18 ■商品番号1108324 | 16,529円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) MT-10 ABS (RN45) MT-10 SP ABS (RN45) MT-10 TOURER EDITION (RN45) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-918H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European license plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-specific bracket with mounting parts - HIGHSIDER AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - For the original turn signals， the special turn signal bracket 280-984 is optionally available． - If your original number plate holder has reflectors fitted to the side， these must be refitted in a suitable position or replaced with new ones． Tips: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種MT-10 ABS (RN45) MT-10 ABS (RN45) 年式: 16-21 MT-10 SP ABS (RN45) MT-10 SP ABS (RN45) 年式: 17-21 MT-10 TOURER EDITION (RN45) MT-10 TOURER EDITION (RN45) 年式: 17-19 ■商品番号1108326 | 14,469円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー Z1000 ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-721HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS PRO’s turn signal brackets are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light Included with the AKRON-RS PRO are: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-approved reflector with adjustable bracket - E-approved license plate light - Mounting instructions Note:The special 280-974 turn signal bracket is available as an option for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種Z1000 Z1000 ■商品番号1108239 | 18,588円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) CB 650 F (RC75) CB 650 F ABS (RC75) CB 650 F ABS (RC97) CBR 650 F (RC74) CBR 650 F ABS (RC74) CBR 650 F ABS (RC96) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-610H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS turn signal brackets are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesThe scope of delivery of the AKRON-RS includes: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Note:The special turn signal bracket 280-973 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種CB 650 F (RC75) CB 650 F (RC75) 年式: 14-16 CB 650 F ABS (RC75) CB 650 F ABS (RC75) 年式: 14-16 CB 650 F ABS (RC97) CB 650 F ABS (RC97) 年式: 17-18 CBR 650 F (RC74) CBR 650 F (RC74) 年式: 14-16 CBR 650 F ABS (RC74) CBR 650 F ABS (RC74) 年式: 14-16 CBR 650 F ABS (RC96) CBR 650 F ABS (RC96) 年式: 17-19 ■商品番号1108172 | 14,469円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-691HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets on the HIGHSIDER AKRON-RS PRO are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the HIGHSIDER AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European license plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-tested - infinitely adjustable license plate light - many different options for mounting the license plate light The scope of delivery of the HIGHSIDER AKRON-RS PRO includes: - Model-specific bracket with mounting hardware - HIGHSIDER AKRON-RS license plate retainer plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - E-tested license plate light - Mounting instructions Tip: Should you not have found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．Notes: If side reflectors are fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■商品番号1108192 | 18,588円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー YZF-R6 ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-902HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets on the HIGHSIDER AKRON-RS PRO are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the HIGHSIDER AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light The scope of delivery of the HIGHSIDER AKRON-RS PRO includes: - Model-specific bracket with mounting parts - HIGHSIDER AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-approved reflector with adjustable bracket - E-approved license plate light - Mounting instructions Notes: - If side reflectors are fitted to your original license plate holder， these must be refitted in a suitable position or replaced with new ones． - The special turn signal holder 280-977 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種YZF-R6 YZF-R6 ■商品番号1108302 | 18,588円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) RS660 Tuono660 ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-008H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS turn signal brackets are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European license plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the AKRON-RS are: - Model-related bracket with mounting parts - AKRON-RS license plate retainer - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - For the original turn signals， a special turn signal bracket is optionally available in the accessories tab． - If your original number plate holder has reflectors fitted to the side， these must be refitted in a suitable position or replaced with new ones． Tips: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種RS660 RS660 Tuono660 Tuono660 ■商品番号1108073 | 18,588円 |