Akron [車用品・バイク用品]
166件中 31件 - 60件
1 2 3 4 5 6
| 商品 | 説明 | 価格 |
|---|---|---|
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-906H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-related bracket with mounting parts - HIGHSIDER AKRON-RS license plate retaining plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - For the original turn signals the special turn signal holder 280-970 is optionally available． Tips: If you have not found a model-specific license plate holder for your vehicle， then you will certainly find the universal license plate holders from HIGHSIDER， which are available in many different designs．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■商品番号1108309 | 14,469円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) SPEED TRIPLE 1050 ABS SPEED TRIPLE 1050 R ABS SPEED TRIPLE 1050 RS SPEED TRIPLE 1050 S ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-406H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS turn signal brackets are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesIncluded with the AKRON-RS are: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - The special turn signal holder 280-978 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種SPEED TRIPLE 1050 ABS SPEED TRIPLE 1050 ABS 年式: 16 SPEED TRIPLE 1050 R ABS SPEED TRIPLE 1050 R ABS 年式: 16-17 SPEED TRIPLE 1050 RS SPEED TRIPLE 1050 RS 年式: 18-21 SPEED TRIPLE 1050 S SPEED TRIPLE 1050 S 年式: 16-21 ■商品番号1108155 | 16,529円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) YZF-R125 (RE11) YZF-R125 ABS (RE11) YZF-R125 ABS (RE29) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-914H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-related bracket with mounting parts - HIGHSIDER AKRON-RS license plate retaining plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - For the original turn signals the special turn signal holder 280-970 is optionally available． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種YZF-R125 (RE11) YZF-R125 (RE11) 年式: 14-16 YZF-R125 ABS (RE11) YZF-R125 ABS (RE11) 年式: 15-16 YZF-R125 ABS (RE29) YZF-R125 ABS (RE29) 年式: 17-18 ■商品番号1108318 | 14,469円 |
 Highsider ハイサイダー Akron-LS バーエンド ウェビック 楽天市場店 | ■商品概要【メーカー品番】161-0591標準カラー：シルバー■詳細説明HIGHSIDER AKRON-LS Bar End Weights， black with cap in different colors- Styling for your bike -With these nobly designed Bar End Weights with handlebar end mirror receptacle， you can design your bike in detail according to your ideas． These end pieces are used for all HIGHSIDER & SHIN YO handlebar end mirrors with handlebar outer clamp． Handlebar ends also serve to reduce annoying vibrations on the handlebars． Thanks to clamping system with different sleeves universal suitable for 7/8 (Φ22 mm)， 1 inch (Φ25，4 mm) or X-Bar (Φ28，6 mm) tube handlebars with an inner diameter from 12 to 22 mm．Our accessories TIP:Excellent in combination with the visually coordinated design LENKERGRIFFGUMMIS AKRON from our own house． The caps of the handlebar ends mirror the design of the grip rubbers and make your motorcycle cockpit an eye-catcher． If you do want to switch back to handlebar mirrors， you can easily use the optionally available coloured rings instead of a handlebar end mirror and thus add further colour accents． The colour rings are simply pushed over the end of the handlebar and fastened with the grub screw located on the ring．Precisely matched - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle． With a maximum of quality and functionality you can easily design your bike according to your wishes．Dimensions:Bar End WeightsΦ: 37，4 mmWidth: 29 mmMount for mirror: Φ 29，90 mm， Width: 12 mmScope of delivery: 1 pair incl．Each 2 clamping sleeves with D． 12 mm and D． 16 mmEach 2 spacer sleeves with D． 14 mm， D． 18 mm and D． 21 mm2 x M6 central screws2 x M6 cone nutsNOTE:For Bar End Weights with clamping system， the ends of the handlebars must not be blocked by threaded inserts or similar．Steering ends do not have to be approved， therefore do not require any test marks， certificates or ABEs．■注意点※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■商品番号1108561002 | 7,657円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー XSR900 ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-921HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets on the HIGHSIDER AKRON-RS PRO are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the HIGHSIDER AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - License plate light， E-approved - Continuously adjustable license plate light - Many different options for mounting the license plate light The scope of delivery of the HIGHSIDER AKRON-RS PRO includes: - Model-specific bracket with mounting parts - HIGHSIDER AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-approved reflector with adjustable bracket - E-approved license plate light - Mounting instructions Notes: - A special turn signal bracket is optionally available for the original turn signals in the accessories tab． - If your original number plate holder has reflectors fitted to the side， these must be refitted in a suitable position or replaced with new ones． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種XSR900 XSR900 ■商品番号1108331 | 21,664円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) 790 DUKE ABS 790 DUKE ABS L (A2) 890 DUKE 890 DUKE R ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-312H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-related bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European license plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-related bracket with mounting parts - HIGHSIDER AKRON-RS license plate retaining plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - Since the original tail light of your motorcycle is omitted when mounting this license plate holder， we offer you a suitable replacement in the accessories tab． There you will find our modern and for road traffic approved 3in1 combinations． - If your original number plate holder has reflectors fitted to the side， these must be refitted in a suitable position or replaced with new ones． - For the original turn signals we offer you， also in the tab accessories， optionally a special turn signal holder． Tips: If you have not found a model-specific license plate holder for your vehicle， then you will certainly find the universal license plate holders from HIGHSIDER， which are available in many different designs．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種790 DUKE ABS 790 DUKE ABS 年式: 18-20 790 DUKE ABS L (A2) 790 DUKE ABS L (A2) 年式: 18-20 890 DUKE 890 DUKE 年式: 21 890 DUKE R 890 DUKE R 年式: 20-21 ■商品番号1108129 | 14,469円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー XSR 700 ABS (RM11) XSR 700 SPECIAL EDITION ABS (RM11RM12) XSR 700 XTRIBUTE ABS (RM12) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-927Hカラー：ブラック認証：CE 認証素材：スチール■詳細説明The HIGHSIDER AKRON-RS license plate holder fits perfectly on your motorcycle thanks to its attractive design．The license plate holder is model specific and allows easy mounting on the original mountings without any modifications．Made of 2mm steel and laser cut， the holder has a weather resistant coating．Fully adjustable， you can adjust the holder to the desired position． An additional locking screw ensures that it stays in place．The AKRON-RS turn signal holders are adjustable in width and are therefore suitable for all types of turn signals． This adjustment option allows you to adapt the position of your turn signals to the most diverse license plates． The 10 mm holes are on the side to allow the indicators to be mounted without disconnecting them from the wiring harness．Adjustable reflector， E-approvedSuitable for European license platesAdjustable angle of inclinationAdditional screw for optimal positional safetyEasy mounting without additional drillingEasy mounting of the license plate■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種XSR 700 ABS (RM11) XSR 700 ABS (RM11) 年式: 16-21 XSR 700 SPECIAL EDITION ABS (RM11RM12) XSR 700 SPECIAL EDITION ABS (RM11RM12) 年式: 16 XSR 700 XTRIBUTE ABS (RM12) XSR 700 XTRIBUTE ABS (RM12) 年式: 19-21 ■商品番号1111132 | 20,649円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー 990SuperDukeR ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-304HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets on the HIGHSIDER AKRON-RS PRO are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the HIGHSIDER AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light The scope of delivery of the HIGHSIDER AKRON-RS PRO includes: - Model-specific bracket with mounting parts - HIGHSIDER AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-approved reflector with adjustable bracket - E-approved license plate light - Mounting instructions Notes: - If side reflectors are fitted to your original license plate holder， these must be refitted in a suitable position or replaced with new ones． - For the original turn signals the special turn signal holder 280-975 is optionally available． Tip: If you have not found a model-specific license plate holder for your vehicle， then you will certainly find the universal license plate holders from HIGHSIDER， which are available in many different designs．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種990SuperDukeR 990SuperDukeR ■商品番号1108118 | 18,588円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー CBR1000RR Fireblade ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-613HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS PRO’s turn signal brackets are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light Included with the AKRON-RS PRO are: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-approved reflector with adjustable bracket - E-approved license plate light - Mounting instructions Note:The special 280-979 turn signal bracket is available as an option for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種CBR1000RR Fireblade CBR1000RR Fireblade ■商品番号1108179 | 20,649円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー Z900 Z H2 ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-724HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets on the HIGHSIDER AKRON-RS PRO are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the HIGHSIDER AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light The scope of delivery of the HIGHSIDER AKRON-RS PRO includes: - Model specific bracket with mounting hardware - HIGHSIDER AKRON-RS license plate retainer plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - E-tested license plate light - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - The special turn signal holder 280-974 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種Z900 Z900 Z H2 Z H2 ■商品番号1108247 | 18,588円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) GSX-R 125 ABS GSX-R 125 ABS SPECIAL EDITION GSX-S125 GSX-S125 SPECIAL EDITION ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-823H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-related bracket with mounting parts - HIGHSIDER AKRON-RS license plate retaining plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - The special turn signal holder 280-976 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種GSX-R 125 ABS GSX-R 125 ABS 年式: 18-21 GSX-R 125 ABS SPECIAL EDITION GSX-R 125 ABS SPECIAL EDITION 年式: 18 GSX-S125 GSX-S125 年式: 18-21 GSX-S125 SPECIAL EDITION GSX-S125 SPECIAL EDITION 年式: 18 ■商品番号1108293 | 14,469円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー Z1000 ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-721HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS PRO’s turn signal brackets are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light Included with the AKRON-RS PRO are: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-approved reflector with adjustable bracket - E-approved license plate light - Mounting instructions Note:The special 280-974 turn signal bracket is available as an option for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種Z1000 Z1000 ■商品番号1108239 | 18,588円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) CB 650 F (RC75) CB 650 F ABS (RC75) CB 650 F ABS (RC97) CBR 650 F (RC74) CBR 650 F ABS (RC74) CBR 650 F ABS (RC96) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-610H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS turn signal brackets are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesThe scope of delivery of the AKRON-RS includes: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Note:The special turn signal bracket 280-973 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種CB 650 F (RC75) CB 650 F (RC75) 年式: 14-16 CB 650 F ABS (RC75) CB 650 F ABS (RC75) 年式: 14-16 CB 650 F ABS (RC97) CB 650 F ABS (RC97) 年式: 17-18 CBR 650 F (RC74) CBR 650 F (RC74) 年式: 14-16 CBR 650 F ABS (RC74) CBR 650 F ABS (RC74) 年式: 14-16 CBR 650 F ABS (RC96) CBR 650 F ABS (RC96) 年式: 17-19 ■商品番号1108172 | 14,469円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー CB125R ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-614HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS PRO’s turn signal brackets are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light Included with the AKRON-RS PRO are: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-approved reflector with adjustable bracket - E-approved license plate light - Mounting instructions Note:The special 280-979 turn signal bracket is available as an option for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種CB125R CB125R ■商品番号1108181 | 20,649円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) YZF-R1 (RN09) YZF-R6 (RJ05) YZF-R6 (RJ09) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-903H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS turn signal brackets are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixing without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesIncluded with the AKRON-RS are: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - The special turn signal holder 280-977 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種YZF-R1 (RN09) YZF-R1 (RN09) 年式: 02-03 YZF-R6 (RJ05) YZF-R6 (RJ05) 年式: 03 YZF-R6 (RJ09) YZF-R6 (RJ09) 年式: 04-05 ■商品番号1108305 | 14,469円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) MT-125 ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-925H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-related bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European license plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-specific bracket with mounting parts - HIGHSIDER AKRON-RS license plate retaining plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructionsNote:If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． Tips: If you have not found a model-specific license plate holder for your vehicle， then you will certainly find the universal license plate holders from HIGHSIDER， which are available in many different designs．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種MT-125 MT-125 年式: 20-21 ■商品番号1108342 | 16,529円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー XSR 700 ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-927HPカラー：ブラック認証：CE 認証素材：スチール■詳細説明The HIGHSIDER AKRON-RS license plate holder fits perfectly on your motorcycle thanks to its attractive design．The license plate holder is model specific and allows easy mounting on the original mountings without any modifications．Made of 2mm steel and laser cut， the holder has a weather resistant coating．Fully adjustable， you can adjust the holder to the desired position． An additional locking screw ensures that it stays in place．The AKRON-RS turn signal holders are adjustable in width and are therefore suitable for all types of turn signals． This adjustment option allows you to adapt the position of your turn signals to the most diverse license plates． The 10 mm holes are on the side to allow the indicators to be mounted without disconnecting them from the wiring harness．The PRO version of the HIGHSIDER AKRON-RS includes a high-quality aluminum license plate light with mounting plate and support arm． The bracket is height-adjustable and designed for an homolgated mounting．Adjustable reflector， E-approvedSuitable for European license platesAdjustable angle of inclinationAdditional screw for optimal positional safetyEasy mounting without additional drillingEasy mounting of the license plateAdjustable plate light included， holder included■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種XSR 700 XSR 700 ■商品番号1111133 | 23,617円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー Ninja400 Z400 ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-727HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets on the HIGHSIDER AKRON-RS PRO are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the HIGHSIDER AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light The scope of delivery of the HIGHSIDER AKRON-RS PRO includes: - Model specific bracket with mounting hardware - HIGHSIDER AKRON-RS license plate retainer plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - E-tested license plate light - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - The special turn signal holder 280-974 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種Ninja400 Ninja400 Z400 Z400 ■商品番号1108253 | 18,588円 |
 Highsider ハイサイダー Akron-LS バーエンド ウェビック 楽天市場店 | ■商品概要【メーカー品番】161-0595標準カラー：チタン■詳細説明HIGHSIDER AKRON-LS Bar End Weights， black with cap in different colors- Styling for your bike -With these nobly designed Bar End Weights with handlebar end mirror receptacle， you can design your bike in detail according to your ideas． These end pieces are used for all HIGHSIDER & SHIN YO handlebar end mirrors with handlebar outer clamp． Handlebar ends also serve to reduce annoying vibrations on the handlebars． Thanks to clamping system with different sleeves universal suitable for 7/8 (Φ22 mm)， 1 inch (Φ25，4 mm) or X-Bar (Φ28，6 mm) tube handlebars with an inner diameter from 12 to 22 mm．Our accessories TIP:Excellent in combination with the visually coordinated design LENKERGRIFFGUMMIS AKRON from our own house． The caps of the handlebar ends mirror the design of the grip rubbers and make your motorcycle cockpit an eye-catcher． If you do want to switch back to handlebar mirrors， you can easily use the optionally available coloured rings instead of a handlebar end mirror and thus add further colour accents． The colour rings are simply pushed over the end of the handlebar and fastened with the grub screw located on the ring．Precisely matched - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle． With a maximum of quality and functionality you can easily design your bike according to your wishes．Dimensions:Bar End WeightsΦ: 37，4 mmWidth: 29 mmMount for mirror: Φ 29，90 mm， Width: 12 mmScope of delivery: 1 pair incl．Each 2 clamping sleeves with D． 12 mm and D． 16 mmEach 2 spacer sleeves with D． 14 mm， D． 18 mm and D． 21 mm2 x M6 central screws2 x M6 cone nutsNOTE:For Bar End Weights with clamping system， the ends of the handlebars must not be blocked by threaded inserts or similar．Steering ends do not have to be approved， therefore do not require any test marks， certificates or ABEs．■注意点※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■商品番号1108561005 | 7,657円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー MT-125 ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-925HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets on the HIGHSIDER AKRON-RS PRO are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the HIGHSIDER AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - License plate light， E-approved - Continuously adjustable license plate light - Many different options for mounting the license plate light The scope of delivery of the HIGHSIDER AKRON-RS PRO includes: - Model specific bracket with mounting hardware - HIGHSIDER AKRON-RS license plate retainer plate - Adjustable turn signal brackets - E-approved reflector with adjustable bracket - E-approved license plate light - Mounting instructions Charging license plate light: - White = Plus - Black = GroundNote: If there are any side reflectors fitted to your original number plate holder， these will need to be refitted in a suitable position or replaced with new ones．Tip: If you haven’t found a model-specific license plate holder for your vehicle， then you’re sure to find what you’re looking for with the universal license plate holders from HIGHSIDER， which are available in many different designs．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種MT-125 MT-125 ■商品番号1108343 | 20,649円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー CB650R CBR650R ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-618HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets on the HIGHSIDER AKRON-RS PRO are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the HIGHSIDER AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light The scope of delivery of the HIGHSIDER AKRON-RS PRO includes: - Model specific bracket with mounting hardware - HIGHSIDER AKRON-RS license plate retainer plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - E-tested license plate light - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - The special turn signal holder 280-979 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種CB650R CB650R CBR650R CBR650R ■商品番号1108188 | 20,649円 |
 Highsider ハイサイダー Akron-XL ハンドルバーウエイト ウェビック 楽天市場店 | ■商品概要【メーカー品番】161-0572標準カラー：レッド■詳細説明HIGHSIDER AKRON-XS motorcycle Bar End Weights- Styling for your bike -With these nobly designed handlebar ends you can design your bike in detail according to your ideas． Handlebar ends also serve to reduce annoying vibrations on the handlebars． Thanks to clamping system with different sleeves universal suitable for 7/8 (Φ22 mm)， 1 inch (Φ25，4 mm) or X-Bar (Φ28，6 mm) tube handlebars with an inner diameter from 12 to 22 mm．Our accessories TIP:Excellent in combination with the visually coordinated design LENKERGRIFFGUMMIS from our own house． The caps of the handlebar ends mirror the design of the grip rubbers and make your motorcycle cockpit an eye-catcher．Precisely matched - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle． With a maximum of quality and functionality you can easily design your bike according to your wishes．Dimensions:Stem weightΦ: 37，4 mmWidth: 17 mmScope of supply: 1 pair incl．2 clamping sleeves each with D． 12 mm and D． 16 mm2 spacer sleeves each with D． 14 mm， D． 18 mm and D． 21 mm2 x M6 central screws2 x M6 cone nutsNOTE:For Bar End Weights with clamping system， the ends of the handlebars must not be blocked by threaded inserts or similar．Steering ends do not have to be approved， therefore do not require any test marks， certificates or ABEs．■注意点※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■商品番号1108559003 | 7,657円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー GSX-R125 GSX-S125 ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-823HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS PRO’s turn signal brackets are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light Included with the AKRON-RS PRO are: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-approved reflector with adjustable bracket - E-approved license plate light - Mounting instructions Note:The special 280-976 turn signal bracket is available as an option for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種GSX-R125 GSX-R125 GSX-S125 GSX-S125 ■商品番号1108294 | 18,588円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー CB1000R ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-615HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The AKRON-RS PRO’s turn signal brackets are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light Included with the AKRON-RS PRO are: - Model-specific bracket with mounting parts - AKRON-RS license plate mounting plate - Adjustable turn signal brackets - E-approved reflector with adjustable bracket - E-approved license plate light - Mounting instructions Note:The special turn signal bracket 280-983 is available as an option for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種CB1000R CB1000R ■商品番号1108183 | 20,649円 |
 Highsider ハイサイダー Akron-RS プロ ナンバープレートホルダー Hypermotard950 ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-165HP■詳細説明HIGHSIDER AKRON-RS PRO license plate holder incl． license plate lightThe HIGHSIDER AKRON-RS PRO license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS PRO allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets on the HIGHSIDER AKRON-RS PRO are adjustable in width， making them suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Included in this PRO version of the HIGHSIDER AKRON-RS is the very small HIGHSIDER license plate light machined from high quality aluminum with mounting plate and support arm． The bracket is adjustable in height and designed to allow mounting in the legally required position．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (eg．e．g． drilling) - easy mounting of the license plate through slotted holes - license plate light incl． Holder included - license plate light， E-approved - infinitely adjustable license plate light - many different options for mounting the license plate light The scope of delivery of the HIGHSIDER AKRON-RS PRO includes: - Model specific bracket with mounting hardware - HIGHSIDER AKRON-RS license plate retainer plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - E-tested license plate light - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - The special turn signal holder 280-969 is optionally available for the original turn signals． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種Hypermotard950 Hypermotard950 ■商品番号1108108 | 21,664円 |
 Highsider ハイサイダー Akron ハンドルバーグリップ ゴム ウェビック 楽天市場店 | ■商品概要【メーカー品番】315-0573標準カラー：Titanium7/8 インチ (22．2 mm) 132 mm■詳細説明HIGHSIDER AKRON handlebar grip rubber， black with aluminum ring in different colors - Styling for your bike - The stylish 7/8 inch handlebar grips HIGHSIDER AKRON create with the superimposition of the two aluminum sleeves a new kind of design language． The outer embodies timeless design with its lines and forms a beautiful contrast with the trapezoidal tongues to the underlying bead-blasted black aluminum cylinder． The HIGHSIDER lettering is incorporated into the handle structure． The removable end caps allow the mounting of handlebar end indicators， handlebar end mirrors or handlebar weights． With these grips， you can give your bike the noble HIGHSIDER look and enhance its appearance． Our accessories TIP: Excellent in combination with the visually matched design handlebar weights from our own house． The handlebar ends pick up the design of the rubber grips and turn your motorcycle cockpit into an eye-catcher． Tailor-made for your bike - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle． With a maximum of quality and functionality you can easily design your bike according to your wishes． Dimensions:Fits for 7/8 inch (22 mm) Length: 132 mm Outside diameter rubber: approx 34 mm Outside diameter aluminum sleeve: approx 37 mm Scope of delivery: 1 pair■注意点※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■商品番号1108698003 | 8,760円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー PANIGALE V2 PANIGALE V4 PANIGALE V4 25 ANNIVERSARIO 916 PANIGALE V4 R PANIGALE V4 S PANIGALE V4 S CORSE PANIGALE V4 SPECIALE STREETFIGHTER V4 STREETFIGHTER V4 S ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-164Hカラー：ブラック認証：CE 認証素材：スチール■詳細説明The HIGHSIDER AKRON-RS license plate holder fits perfectly on your motorcycle thanks to its attractive design．The license plate holder is model specific and allows easy mounting on the original mountings without any modifications．Made of 2mm steel and laser cut， the holder has a weather resistant coating．Fully adjustable， you can adjust the holder to the desired position． An additional locking screw ensures that it stays in place．The AKRON-RS turn signal holders are adjustable in width and are therefore suitable for all types of turn signals． This adjustment option allows you to adapt the position of your turn signals to the most diverse license plates． The 10 mm holes are on the side to allow the indicators to be mounted without disconnecting them from the wiring harness．Adjustable reflector， E-approvedSuitable for European license platesAdjustable angle of inclinationAdditional screw for optimal positional safetyEasy mounting without additional drillingEasy mounting of the license plate■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■商品番号1111151 | 16,529円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー MT-09 ABS (RN43) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-928Hカラー：ブラック認証：CE 認証素材：スチール■詳細説明The HIGHSIDER AKRON-RS license plate holder fits perfectly on your motorcycle thanks to its attractive design．The license plate holder is model specific and allows easy mounting on the original mountings without any modifications．Made of 2mm steel and laser cut， the holder has a weather resistant coating．Fully adjustable， you can adjust the holder to the desired position． An additional locking screw ensures that it stays in place．The AKRON-RS turn signal holders are adjustable in width and are therefore suitable for all types of turn signals． This adjustment option allows you to adapt the position of your turn signals to the most diverse license plates． The 10 mm holes are on the side to allow the indicators to be mounted without disconnecting them from the wiring harness．Adjustable reflector， E-approvedSuitable for European license platesAdjustable angle of inclinationAdditional screw for optimal positional safetyEasy mounting without additional drillingEasy mounting of the license plate■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種MT-09 ABS (RN43) MT-09 ABS (RN43) 年式: 21 ■商品番号1111134 | 16,529円 |
 Highsider ハイサイダー Akron-RS ナンバープレートホルダー (ライト なし) MT-07 MT-07 (RM04) MT-07 ABS (RM04) MT-07 ABS (RM17RM18) MT-07 MOTO CAGE (RM04) MT-07 MOTO CAGE ABS (RM04) ウェビック 楽天市場店 | ■商品概要【メーカー品番】280-913H■詳細説明HIGHSIDER AKRON-RS license plate holderThe HIGHSIDER AKRON-RS license plate holder adapts perfectly to the lines of your bike thanks to its design．The model-specific bracket of the HIGHSIDER AKRON-RS allows mounting on the original mounting points of your bike and thus a replacement without further drilling or cutting． To prevent damage to cables， all sharp-edged feedthroughs are protected by a rubber membrane grommet． The license plate is made of sheet steel and 2 mm thick． The precise cutting is done by laser． After edging， the weather-resistant black powder coating is applied．This ensures the optimal fit and durability．Through the stepless adjustment you can bring the plate without drilling in the desired position． To keep the plate in this position， there is an additional locking screw．The turn signal brackets of the HIGHSIDER AKRON-RS are adjustable in width and therefore suitable for any type of accessory turn signal． This adjustment option allows you to adapt the position for your turn signals to the most varied number plates． To allow mounting the turn signals without disconnecting them from the wiring harness， the 10 mm holes are slotted to the side．You can also adjust the position of the reflector individually via a slider． An adaptation to the different designs of the EU license plates is therefore no problem．To screw the license plate securely and reduce vibration， two rubber washers are included． Another rubber buffer supports the license plate on its underside．Details: - model-specific bracket - infinitely adjustable turn signal holder - slotted turn signal holder for easy mounting without cable separation - infinitely adjustable reflector， E-approved - suitable for European number plates - infinitely adjustable tilt angle - additional screw for optimum position security - easy fixation without further work steps (e． g．B． Drilling) - easy mounting of the license plate through slotted holesIncluded in the scope of delivery of the HIGHSIDER AKRON-RS are: - Model-related bracket with mounting parts - HIGHSIDER AKRON-RS license plate retaining plate - Adjustable turn signal brackets - E-tested reflector with adjustable bracket - Mounting instructions Notes: - If there are side reflectors fitted to your original number plate holder， these must be refitted in a suitable position or replaced with new ones． - For the original turn signals the special turn signal holder 280-984 is optionally available． Tip: If you have not found a model-specific license plate holder for your vehicle， the universal license plate holders from HIGHSIDER， which are available in many different designs， are certainly a good alternative．■注意点※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■適合車種MT-07 MT-07 年式: 21 MT-07 (RM04) MT-07 (RM04) 年式: 14-16 MT-07 ABS (RM04) MT-07 ABS (RM04) 年式: 14-16 MT-07 ABS (RM17RM18) MT-07 ABS (RM17RM18) 年式: 17-20 MT-07 MOTO CAGE (RM04) MT-07 MOTO CAGE (RM04) 年式: 14-16 MT-07 MOTO CAGE ABS (RM04) MT-07 MOTO CAGE ABS (RM04) 年式: 14-16 ■商品番号1108316 | 14,469円 |
 Highsider ハイサイダー Akron-LS バーエンド ウェビック 楽天市場店 | ■商品概要【メーカー品番】161-0593標準カラー：マットチタン■詳細説明HIGHSIDER AKRON-LS Bar End Weights， black with cap in different colors- Styling for your bike -With these nobly designed Bar End Weights with handlebar end mirror receptacle， you can design your bike in detail according to your ideas． These end pieces are used for all HIGHSIDER & SHIN YO handlebar end mirrors with handlebar outer clamp． Handlebar ends also serve to reduce annoying vibrations on the handlebars． Thanks to clamping system with different sleeves universal suitable for 7/8 (Φ22 mm)， 1 inch (Φ25，4 mm) or X-Bar (Φ28，6 mm) tube handlebars with an inner diameter from 12 to 22 mm．Our accessories TIP:Excellent in combination with the visually coordinated design LENKERGRIFFGUMMIS AKRON from our own house． The caps of the handlebar ends mirror the design of the grip rubbers and make your motorcycle cockpit an eye-catcher． If you do want to switch back to handlebar mirrors， you can easily use the optionally available coloured rings instead of a handlebar end mirror and thus add further colour accents． The colour rings are simply pushed over the end of the handlebar and fastened with the grub screw located on the ring．Precisely matched - the extensive range of accessories from HIGHSIDER is perfectly tailored to your motorcycle． With a maximum of quality and functionality you can easily design your bike according to your wishes．Dimensions:Bar End WeightsΦ: 37，4 mmWidth: 29 mmMount for mirror: Φ 29，90 mm， Width: 12 mmScope of delivery: 1 pair incl．Each 2 clamping sleeves with D． 12 mm and D． 16 mmEach 2 spacer sleeves with D． 14 mm， D． 18 mm and D． 21 mm2 x M6 central screws2 x M6 cone nutsNOTE:For Bar End Weights with clamping system， the ends of the handlebars must not be blocked by threaded inserts or similar．Steering ends do not have to be approved， therefore do not require any test marks， certificates or ABEs．■注意点※輸入品のため、説明書が付属する場合、外国語の説明書となります。※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。 ※画像はイメージです。■商品番号1108561004 | 7,657円 |